Oven wouldn't warm up before a holiday dinner. The bake element had burned through. Replaced the same day and dinner was on time.
A slow preheat, food burnt on one side, or an error code right before dinner. Our technician tests the heating parts and temperature probe in your kitchen and restores accurate baking heat.
Common Calls
Every common oven fault in one view: what you'll see, why it happens, how we fix it, and what to do before we arrive.
| Problem | What You Notice | Likely Cause | What We Do | While You Wait |
|---|---|---|---|---|
| 01Won't Heat | The light works but the oven stays cold. |
A burned bake element on electric models or a weak igniter on gas models. Bake elementIgniterSafety valve |
Test both with a meter and replace the failed part. |
Check the breaker; with gas, you should hear the igniter after turning the dial. |
| 02Uneven Baking | One end of the sheet chars, the other stays blond. |
A failing convection fan, a weak section of element or heat escaping from the door. Convection fanBake elementDoor gasket |
Map the oven temperature and repair the fan, element or seal. |
Rotate pans halfway and bake on the middle rack. |
| 03Slow Preheat | Preheat takes far longer than it used to. |
A weak igniter or a failed broil element that helps during preheat. IgniterBroil elementBake element |
Meter the igniter plus top and bottom elements; swap the weak one. |
Note the minutes needed to hit 350 °F. |
| 04Wrong Temperature | Recipes burn or come out undercooked. |
The temperature sensor has drifted, so the control heats to the wrong level. Temperature sensorControl boardCalibration |
Measure the sensor and recalibrate or replace it. |
Use an oven thermometer to measure the difference. |
| 05Door Leaking Heat | Heat leaks out at the door edges and the kitchen warms up quickly. |
Worn hinges or a flattened door gasket. Door hingesDoor gasketHinge springs |
Fit new hinges and a fresh seal so the door closes tight. |
Let the door rest half-open; a healthy door stays put or rises. |
| 06Error Codes | Letters flash on the panel and heating stops. |
A sticking touch key, a failed probe, or a relay stuck on the board. Control boardKeypadSensor |
Confirm the cause before quoting any board replacement. |
Note the code plus whatever was in the oven. |
From the builder-grade units in new Hays County subdivisions to premium kitchen suites, our technicians work on every major make you'll find in a Buda home.
Don't see your brand? Call us anyway; chances are we repair it too.
Choose your brand to see the codes that make most often shows. Meanings may shift slightly between model years.
Oven temperature has gone too high.
GE reads an open circuit at the probe.
A function key is stuck or shorted.
Runaway temperature detected; heat has been cut.
The oven sensor or probe circuit is open.
Frigidaire detects a key stuck closed.
The oven temperature sensor is open or shorted.
The keypad or touch panel is faulty.
The door switch isn't reading correctly.
Code still showing after a five-minute power cut? Then book a technician for a proper diagnosis.
Feedback from Buda households after an oven visit.
Oven wouldn't warm up before a holiday dinner. The bake element had burned through. Replaced the same day and dinner was on time.
Cookies burned on one side. Convection fan motor had failed. Even baking now.
Preheat took forever. Igniter needed ordering, two visits, but fast now.
Food kept overcooking. Sensor replaced and recalibrated. Spot on now.
Warm air escaped around the door. New hinges and gasket.
Display showed an error and wouldn't bake. Faulty keypad replaced.
A few minutes here sometimes saves a booking.
Use a thermometer
Set 350 °F, wait twenty minutes, read the thermometer. More than 25 degrees off is worth reporting.
Check the breaker
Ovens run on a double breaker. One tripped side can leave lights on and elements cold.
Inspect the gasket
Look for cracks or gaps in the door seal. Escaping heat slows cooking.
Look at the element
Check the bake element for blisters or breaks. Visible damage means it needs replacing.
Check the lock
A control lock or unfinished self-clean can block baking. Look for a lock symbol.
Confirm the gas
Gas models: make sure the shut-off behind the range is fully on.
Still not baking right after all six?
Book A VisitDrop your name and number below, and someone from our office will ring you to set a time. Let us know the make and what's going wrong so the technician brings the right parts.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.